Creating a TTY Simulator in Assembly Language on the VIC-20

  /     /   Assembly     Commodore     Programming     Retro     VIC-20    

The Vicmon machine language cartridge is an excellent tool for exploring the Vic-20. This article and its associated video will show you how to use it to create a simple program that will change the normal output of a Vic so that it feels a bit like a teletype terminal. This will be done by taking over some of the functionality of the KERNEL's CHROUT subroutine at $FFD2. For those without an easy way of entering an assembly language program, there is a BASIC listing at the end.

Assuming you have the Vicmon cartridge attached to your machine or emulator, you can now enter the monitor. If you are not too familiar with the Vicmon cartridge, have a look at: Beginning Assembly Programming on the Vic-20.

SYS 24576

Each KERNAL subroutine is actually just a jump table to somewhere else. To see where the CHROUT subroutine jumps to, we'll disassemble the code at $FFD2:


Which shows that it contains:

FFD2 JMP ($0326)

This is an indirect jump to the address stored at $0326.

If we now look at $0326:

.M 0326

We see that the first two bytes are 7A F2. The 6502 is little-endian, so it stores the least significant byte first and hence this is address $F27A. Because $0326 is in RAM, we can change the address there to point to our code. Once our routine has been run, we'll jump to $F27A to output the character to screen.

It would be better if our program doesn't interfere with BASIC, so as it is quite small, we can store it in the cassette buffer. This is located at $033C and is 191 bytes long. If you load or save with the cassette, the program will naturally be lost.

The program is essentially in two parts. The first part changes the output vector to point to the second part and sets the volume to maximum. The second part is the routine which will be called when the CHROUT ($FFD2) subroutine jumps to the output vector stored at $0326. This part will output a noise, pause and then jump to the original output vector at $F27A.

The video below shows how to use the Vicmon machine language cartridge to enter the program and demonstrates the TTY effect.

Disassembly of Program

Here is the full program as entered in the video, so that you can play with it yourself.

      ; Initialize the routine
033C  LDA #$03      ; Point output vector used by $FFD2 to our routine
033E  STA $0327     ; |
0341  LDA #$4C      ; |
0343  STA $0326     ; \
0346  LDA #$0F      ; Set the volume to maximum
0348  STA $900E     ; \
034B  RTS

      ; The main routine pointed to by the output vector
034C  PHA           ; Save the character to be printed

034D  CMP #$20      ; Skip making a noise if a space character
034F  BEQ $035A     ; \
0351  CMP #$0D      ; Skip making a noise if a return character
0353  BEQ $035A     ; \

0355  LDA #$80      ; Make the lowest note possible with speaker 2
0357  STA $900B     ; \

035A  TXA           ; Save the registers because $FFD2 doesn't alter them
035B  PHA           ; |
035C  TYA           ; |
035D  PHA           ; \

035E  LDY #$00      ; Delay to hold note if making a noise or give equal gap
0360  LDX #$15      ; |
0362  DEY           ; |
0363  BNE $0362     ; |
0365  DEX           ; |
0366  BNE $0362     ; \

0368  LDA #$00      ; Turn off speaker 2
036A  STA $900B     ; \

036D  LDY #$00      ; Delay between letters
036F  LDX #$10      ; |
0371  DEY           ; |
0372  BNE $0371     ; |
0374  DEX           ; |
0375  BNE $0371     ; \

0377  PLA           ; Restore the registers
0378  TAY           ; |
0379  PLA           ; |
037A  TAX           ; |
037B  PLA           ; \

037C  JMP $F27A     ; Jump to the normal output vector stored in $0326

Memory Dump

Below is a memory dump of the program. Some find it quicker to enter the hex codes directly and this is also useful to create a BASIC program that will load the machine language.

033C  A9 03 8D 27 03
0341  A9 4C 8D 26 03
0346  A9 0F 8D 0E 90
034B  60 48 C9 20 F0
0350  09 C9 0D F0 05
0355  A9 80 8D 0B 90
035A  8A 48 98 48 A0
035F  00 A2 15 88 D0
0364  FD CA D0 FA A9
0369  00 8D 0B 90 A0
036E  00 A2 10 88 D0
0373  FD CA D0 FA 68
0378  A8 68 AA 68 4C
037D  7A F2

I find it quite nice to work with the hex as well as assembly language, particularly when you are debugging as it can be quicker to navigate and find what you are looking for. Here you can see the repeated LDA commands used at the start of the program as A9. You can also see the 20 used to detect a space at $034E. If you wanted to change this character, you could just alter that memory location, instead of reassembling the line.

BASIC Alternative

The following is the program converted to BASIC so that anyone with a Vic can enter it.

20 DATA 169,3,141,39,3,169,76,141,38,3
30 DATA 169,15,141,14,144,96,72,201,32,240
40 DATA 9,201,13,240,5,169,128,141,11,144
50 DATA 138,72,152,72,160,0,162,21,136,208
60 DATA 253,202,208,250,169,0,141,11,144,160
70 DATA 0,162,16,136,208,253,202,208,250,104
80 DATA 168,104,170,104,76,122,242
90 SYS 828

All you have to do is RUN the program and from that point on your Vic will feel a bit like a TTY.

Where now?

For more information on Vicmon or for those just starting to program the Vic-20 in assembly language, take a look at: Beginning Assembly Programming on the Vic-20. I have also created an extended version of the TTY simulator and hosted it on GitHub: vic20_simtty.

Creative Commons License
Creating a TTY Simulator in Assembly Language on the VIC-20 by Lawrence Woodman is licensed under a Creative Commons Attribution 4.0 International License.

Share This Post


Sign up to get new articles straight to your inbox.

Delivered by FeedBurner

Related Articles

Position Independent Code (6502) on the Commodore VIC-20

If we are writing 6502 machine code and want to to create a routine or program that can be placed in any location then we have to create Position Independent Code (PIC) or make the code relocatable. H...   Read More

Adding Basic Stubs to Assembly Language on the Commodore VIC-20

To make machine language programs more friendly it's nice to add a Basic stub which contains a line with a SYS statement to start the code. This is easy to do on the VIC-20 and the process gives you a...   Read More

Hand Assembling to Machine Code on the Commodore VIC-20

I quite enjoy designing machine language routines on paper and then hand assembling them. For many people this would have been their only option until they got a more advanced machine language monitor...   Read More

Beginning Assembly Programming on the Commodore VIC-20

The Commodore Vic-20 is a great machine to learn an assembly language on. It was released in 1981 and was the first computer to sell one million units, which contributes to its popularity today. The ...   Read More

Changing Screen Dimensions on the Commodore VIC-20

To make the most of the limited amount of memory on the VIC-20, we can increase and decrease the screen size depending on our program's priorities and what we want to achieve. If we increase the size ...   Read More